Brisket! Sourdough!

15.5 pound brisket, $3.78 per pound, Sam’s in Idaho Falls, 4 Tbsp salt, 4 Tbsp pepper, 2 Tbsp garlic powder. Gonna put them on at 225℉ to start.

1810, 9 Nov: brisket on the smoker.

1830: sourdough is fermenting.

2200: flat is at 160℉, point at 142℉.

0210, 10 Nov: flat is 166℉, point 164℉. Crutched it!

0730: flat is 186℉, point 187℉. Turned temperature up to 250℉.

0845: put the rest of the ingredients in the bread. I’ve continued doing the 1 tsp regular yeast along with the sourdough starter, and doubling sourdough starter over the Josie Baker recommendation.

0930: flat is 201℉, point 200℉. Almost there!

1000: both are at 202℉. Just one degree more!

1045: sourdough starting bulk rise.

1110: brisket at 203℉. Taking it off.

Cleaned up, sliced up, gotta cool a bit…

1400: sourdough in the pan for final rise.

1712: sourdough in the oven.

Now brisket sandwiches will be almost from scratch… Everything except cheese and BBQ sauce

CybatiWorks PI – Running on QEMU

CybatiWorks is an educational and research tool for learning about Industrial Control System cyber components. I haven’t used it much, but it looks like it’ll simulate a PLC controlling a process, and it’ll do it on a Raspberry PI, GPIO-connected hardware, and a controlling HMI (Human-Machine Interface) desktop. You can buy the hardware pre-setup, then use it in a course.

The person who runs the company is Matthew Luallen, and he’s quite responsive over email. I’ve been trying to look into the system a bit, and CybatiWorks offers the RasPI image for free through their “Community” program. Unfortunately that’s run by Google+, and is now a broken link. Emailing the responsive founder, however, will get you a link to the necessary image.

Now that I had the RasPI image though, I needed to run it, and didn’t have a PI handy. It was time for QEMU. This gentleman had a great start, and following his instructions allowed me to investigate the system partially, but that methodology gets you only 256MB RAM total. I needed more to start up all the services in the image, so I could see them work together.

QEMU’s documentation had a way forward – use the “virt” machine instead of versatile.., but this necessitated building a new kernel. Something I learned during this process – kernels built for one ARM machine don’t seem to work well on others. I’m not 100% why, I’ve definitely seen lots of binaries work interoperably, but kernels seem to be very specific (at least with QEMU).

The RasPI image comes with a kernel, f3n3s7ra’s page recommended a kernel… Unfortunately the QEMU documentation recommends installing a Debian image to get the kernel and initrd. That took several hours – now that I extracted them I’ve got them available for download via the links in the previous sentence (these came from the Debian project on 1 Nov 2019).

Once you’ve got initrd, vmlinuz, and CybatiWorksPI.img extracted from the email Matthew can send you, the command below will startup QEMU with a working network stack and kick you to a shell as root. You may have to switch the window view over to “serial0”.

sudo qemu-system-arm -M virt -m 1024 -kernel vmlinuz-3.16.0-6-armmp-lpae -initrd initrd.img-3.16.0-6-armmp-lpae -drive if=none,file=CybatiWorksPI.img,format=raw,id=hd -device virtio-blk-device,drive=hd -netdev tap,id=ethdev -device virtio-net-device,netdev=ethdev -no-reboot -append "root=/dev/vda2 rootfstype=ext4 rw init=/bin/bash"

You won’t get the typical startup sequence via systemd, and I haven’t been able to get that working yet, but you can do something similar with the command below (from the QEMU command line). This’ll kick off runlevel 3 startup scripts.

cd /etc/rc3.d
for i in S*; do ./$i restart; done

Now an ifconfig should reveal that eth0 is up and at 172.16.192.30/24. Back on your host computer “sudo ip add add 172.16.192.10/24 dev tap0” will configure tap0 to communicate with the QEMU box. You should now be able to ping 172.16.192.30 from your host.

The default services now should be:
TCP 22 – SSH
TCP 80 – lighttpd
TCP 2812 – monit
TCP 7777 – RexWSTCP
TCP 8000 – WebIOPi
TCP 43981 – RexCore

If you want to run the HMI VM Matthew will send you, don’t set your host to 172.16.192.30, so the VM can take that address. After starting the VM up, you may have to configure subnets more intelligently, and IP forwarding on your host (so the different network devices in your host can communicate).